Description:
ETL-certified rotary evaporator package meets UL/CSA requirements. Most municipalities require this certification, which also ensures higher safety standards and a longer equipment lifespan.
The 20L Rotary Evaporator Package includes everything you need to start your solvent recovery process out of the box. As a bonus, it also includes a free dual 10L receiving flask upgrade. The items included in this package are as follows:
- (1) PolyScience 220V 6860 -10°C 13L 1.5HP recirculating chiller with turbine pump
- (1) Welch 220V 2052 2.3 cfm 1.5 torr 4-head diaphragm pump and vacuum hose
- (1) Ai 220V SolventVap 5.3-gallon rotary evaporator and water bath
- (1) Dual main condensers with sleeves
Single auxiliary condenser with sleeve
3-way flask - (1) 5.3G/20L/0.7 cu ft round shaped rotating evaporating flask, glass
- (1) Dual 10L receiving flask
- (1) Reinforced food-grade vacuum & chilling tubing (15 ft.)
- (1) Vapor duct & evaporation flask seal (pre-installed)
- (1) Glass material feeding port with PTFE open/close valve and PTFE extension feeding tube
- (7 sets) QuickClamp and PTFE centering rings
- (1) Ai plexiglass bath cover for 20L SolventVap
Across International’s Official Canadian Distributor of High-Quality Products.
Across International rotary evaporators or rotovaps come with PTFE valves to ensure solvent resistance. Rapid heat-up is made possible by its optimized bath volume. Glass tubes used in the condenser unit have been designed to optimize surface area, thereby increasing evaporation efficiency. A rotary evaporator features a motor and worm gear designed for constant rotation at speeds up to 130 rpm. A thin layer of liquid is constantly transferred over the entire inner surface of the flask containing the solvent. The water bath gently heats the surface, creating a large area for evaporation. Special seals on the rotating system enable it to be placed under vacuum, which reduces the boiling point of the solvents and removes the vapor phase, thereby increasing efficiency. Moreover, each unit is equipped with a vacuum release that is easy to use, which allows continuous feed. The digital water bath operates from ambient temperature to 99C (210F) with 0.1C step-by-step temperature control. Should the controller fail, the overheat protector will shut down the power. Standard Glassware Set contains a 20L round-bottomed evaporating flask, a 10L round-bottomed receiving flask, and a vertical condenser. Distilling solvents with higher boiling points is made easier by rotary evaporators with vertical glass condensers.
How does a Rotary Evaporator work?
Rotary evaporators (sometimes referred to as Rotavap or Rotovap) are used primarily to evaporate the solvent from samples under reduced pressure. Reduced pressure, or vacuum, is achieved by using a lab-grade chemical-resistant vacuum pump. Reduced pressure in the apparatus causes the solvent in the ‘boiling flask’ to boil at a lower temperature than at atmospheric pressure. This method of solvent evaporation is ideal for the Cannabis industry due to Cannabinoids and Terpenes tendency to degrade when exposed to high temperatures. Furthermore, Rotary Evaporators require a chiller that is plumbed into the ‘chilling coils’ where the solvent vapour is phase-changed to a liquid and recollected in the ‘receiving flask’. If done correctly, the solvent recovered will be pure and can be reused in the same or different application. It can be challenging to choose the right setup for your lab due to the wide variety of sizes, manufacturers, and prices of rotary evaporators. This is where Evolved Extraction Solutions can assist.
Specifications
Electrical Specifications | 220V 50/60Hz single phase, 20A, 4300 watt (rotation motor: 300 watts) |
Glass material | High borosilicate glass 3.3 |
Evaporating flask
|
Capacity: 5.28 gallons (20 litres or 0.7 cu ft) |
Maximum load: Not to exceed 60% of the flask’s capacity | |
Sealing flange: 4.9″ diameter | |
Rotation speed: 10 to 130 RPM | |
Evaporating speed: 1 gallon/hour (water), 2 gallon/hour (alcohol) | |
Receiving flask | 2.64 gallon (10 liters or 0.35 cu ft) |
Condenser
|
Glassware: Main + auxiliary triple-circulating cold traps, vertical |
Chilling fluid conneciton: 3/8″ hose barb x 4 (2 on main + 2 on auxiliary) | |
Condensing surface | |
Main condenser: 9,480 cm2 or 10.2 sq ft | |
Auxiliary condenser: 3,580 cm2 or 3.9 sq ft | |
Working environment | 5 to 95F |
Water bath
|
Temperature range: ambient to 99C (210F) |
Temperature controller: Digital | |
Dimensions: 17.5″ diameter x 9.8″ depth x 12″ height | |
Material: stainless steel | |
Media: distilled water only | |
Max. water level: not to exceed 1″ from the top rim of the bath | |
Number of heaters: two | |
Drain port: one | |
Exterior liner: rubber | |
Lifting: motorized | |
Maximum lifting distance: 7.5 inches | |
Vacuum
|
Level: < 3 torrs |
Sealing: PTFE + Viton gaskets | |
Connector: 3/8″ hose barb x 1 | |
Swivel casters | Four, built-in with locks |
Safety | Dry-run, over-temp shut-off, built-in circuit breakers |
Shipping weight | 238 Lb (evaporator), 130 Lb (glassware) |
Unit/shipping dimensions | 49 x 23.5 x 82.5″ / 41 x 24 x 48″ (evaporator), 34 x 29 x 33″ (glassware) (WxDxH) |
Certification | ETL tested to UL and CSA standards |